How To Make A Window Frame For A Garage
How to Build a Window Frame for a Garage
Installing a window in your garage can make a huge divergence by providing more natural lite and assuasive y'all to "air out" the identify during nice weather condition. Professional contractors can do the job apace for a substantial fee, but tackling the project yourself doesn't have to be circuitous, fourth dimension-consuming or expensive.
With some common household tools and a little woodworking know-how, you can build your own window frame. Even if you lot cull not to install the window yourself, having the rough opening ready volition eliminate a lot of the labor (and expense) involved in professional person installation.
- Tape measure
- 2-past-4 lumber
- Level
- Hammer or nail gun
- Framing nails (10d)
- Circular saw
- Reciprocating saw
- 2-by-six lumber (if necessary)
- Forest gum (if necessary)
Tip
To save money and time, choose a standard window size that almost hardware stores or contractors will take on hand (or can chop-chop order). It can be a good idea to postpone stride x until merely before you are fix to install the new window. This is unlikely to crusade meaning delays with installation, and information technology volition relieve you the hassle of having a big, open up hole in your garage wall for an extended time.
-
Determine the measurements of the window you want to install. Add one/two inch around for shims and insulation (i.e., a total of 1 inch to both the vertical and horizontal dimensions) to become the size of your window frame.
-
If your garage is finished, remove the drywall or paneling in the spot where the new window will become. Remove everything from the floor to the ceiling within this space, because you volition demand to place new, full-size studs in the wall frame.
-
Mark your frame width from step ane onto the top and bottom boards of the wall frame, and mark the top and lesser of the frame on whatsoever studs that are inside or immediately outside the opening. Add a pair of extra marks at 1.v and 3 inches beyond your frame width on either side. These volition be where you'll place new studs for your window frame, and so if one or more than existing studs are already in the correct place (or y'all can arrange your placement a fleck), you could relieve some time and materials.
-
Trim two 2-by-4 boards to fit betwixt the top and bottom boards of the wall frame. Put each one into one of the outermost slots you marked in step three, and toenail them (blast through them at an angle) to the wall frame.
-
Identify marks on the new studs to signal where the superlative and bottom of your window frame volition be. Then marker two 1.5-inch slots below the bottom of the frame for a sill (a pair of horizontal ii-by-4s), and an additional altitude in a higher place the frame for a header, whose size will be determined by the dimensions of your window and local building codes.
-
If any old wall studs intersect your window frame area, cut out the portions that fall within the window frame, sill or header.
-
Trim two ii-by-4s to fit between the bottom board of the wall frame and the top of your window frame (but not into or above the header space). Nail these to the full-size studs you placed in step 4.
-
Create a header by trimming a 2-by-4 to the width of the window frame, or by gluing plywood between a pair of two-by-6s (all cut to width as well). Identify the header on top of the short studs from stride 7 and nail it to them and the adjacent full-size studs.
-
Trim two ii-by-4s to the width of the window frame, and nail them together to create a sill. Place the sill onto the sawed-off studs from step 6, and nail it to them and the adjacent full-size studs.
-
Within the rough opening you accept created for the window, use a reciprocating saw to cut through any plywood or sheeting roofing your wall frame and the siding or other exterior roofing on the exterior of your garage.
The Drip Cap
- Installing a window in your garage tin make a huge deviation by providing more natural low-cal and allowing you to "air out" the identify during nice atmospheric condition.
- These will be where you lot'll place new studs for your window frame, and so if one or more existing studs are already in the correct place (or you can adjust your placement a bit), you could save some time and materials.
- Trim ii ii-by-4s to fit betwixt the bottom lath of the wall frame and the top of your window frame (but not into or above the header space).
- Place the header on top of the curt studs from step seven and nail it to them and the next full-size studs.
- Within the rough opening yous accept created for the window, use a reciprocating saw to cutting through any plywood or sheeting covering your wall frame and the siding or other exterior covering on the outside of your garage.
Source: https://homesteady.com/13403253/how-to-build-a-window-frame-for-a-garage
Posted by: macksorece.blogspot.com
0 Response to "How To Make A Window Frame For A Garage"
Post a Comment